Skip to content
De Huiszwaluw – vintage interiors
Collection NL

Plywood and bent wood

From the library of

Plywood is wood built up in layers. Thin sheets of veneer are glued on top of one another, each layer at right angles to the one before. The result is a board that is stronger and more stable than a plank of the same thickness, and one you can bend in a mould. That is why it is found in so many chairs, cabinets and tables of the twentieth century: you can make shapes with it that cannot be made in solid wood.

What it is

A tree yields veneer when the trunk is sliced or peeled into thin sheets. In plywood those sheets are stacked and glued, with the grain of each layer at right angles to the grain of the layer below. Wood shrinks and swells mainly across the grain. Crossing the layers makes them hold one another in check. The board hardly moves, is less likely to split at the edge and does not warp.

The number of layers is almost always odd, so that the board is balanced: the outer layers then run in the same direction. In the Netherlands three layers are called triplex and more layers multiplex. In English it is all plywood.

For furniture, plywood is usually made of hardwood: birch and beech are the best known. Birch is pale and strong. It was even used for aircraft: the fuselage of the British de Havilland Mosquito was made of birch plywood.

An old idea, a new industry

The principle is very old. In ancient Egypt, around 2600 BC, wood was already being glued in crossed layers. It was only done on a large scale from the 1850s. In New York the cabinetmaker John Henry Belter was granted a patent in 1858 for a way of pressing chair backs of layered wood in a mould. From the 1880s plywood came on to the market in large quantities, at first mainly for tea chests and packing cases.

Bentwood is something else

There are two ways to bend wood. The first is with steam. In the 1830s Michael Thonet first tried it with glued, bent slats; his chair from Boppard of 1836 was the first successful example. His breakthrough came when he learnt to bend solid beech in hot steam. His chair No. 14 of 1859 consists of six bent parts, and by 1930 about fifty million had been sold.

The second way is that of plywood: laying thin layers in a mould with glue between them and letting them set. The wood then holds its shape by itself. On a steamed part you see one continuous grain. On a layered part you see the layers at the edge.

Aalto, Breuer and the Eameses

The Finnish architect Alvar Aalto showed what bent birch can do. For the sanatorium at Paimio he designed an armchair of bent birch in 1932, meant for patients who had to sit in it for hours each day. In 1933 came his Stool 60, with legs of bent laminated birch. In 1935 he and others founded Artek, which went on to sell his furniture.

In London Jack Pritchard, the founder of Isokon, saw that work and wanted to make something like it himself. He asked Marcel Breuer, who had come to England from Germany. In 1935 and 1936 Breuer drew the Long Chair: a frame of laminated birch with a continuous seat and back of bent plywood. The first seats came from Estonia and were fitted to the frame in London.

In California Charles and Ray Eames went a step further. They learnt to bend plywood in two directions at once. In 1942 the US Navy asked them for a light, stackable leg splint; about 150,000 of these were made. With that knowledge they made their chairs after the war, with a separate seat and back of moulded plywood, built first by Evans in California and later by Herman Miller in Michigan.

Danish shells and Pastoe

In Denmark Arne Jacobsen drew the Ant in 1952, for the canteen of the pharmaceutical company Novo. Seat and back are a single shell of laminated veneer pressed into shape. Fritz Hansen hesitated, but the order for three hundred chairs settled the matter. In 1955 came the Series 7, of which more than five million have been made.

In the Netherlands it was Cees Braakman, designer at the Utrecht furniture maker Pastoe, who took up the material. After a journey to the United States, where he visited the Herman Miller factory, he began working with bent plywood. His chair SB02 in three-ply birch is in the Centraal Museum in Utrecht, dated 1950, with the note that it was inspired by a design by Eames. The chair belongs to Pastoe’s Berkenserie, the Birch Series.

Types, and what it is confused with

Plywood is often confused with solid wood faced with veneer, and with chipboard. Look at the edge and the mistake is soon cleared up. Solid wood shows one grain, chipboard a grainy mass of chips, plywood a stack of stripes.

A special variant is resin-impregnated compressed wood, known under the brand name Pagholz. There the veneer is much thinner and soaked in resin, so that it becomes almost a plastic. It has a book of its own on this shelf.

How to recognise it

Look for an unfinished edge: the underside of a seat, the back edge of a top, the inside of a drawer. There you see the layers as fine lines, alternately light and dark, because you are looking by turns at the end and at the side of the grain. Count them: the number is almost always odd. On a chair shell the lines follow the curve.

Birch plywood is pale. A shell of moulded plywood is thin and light, and gives a little when you sit down.

What to look for when you buy

The weak point of old plywood is the glue. Plywood for indoor use is bonded with glue that stands up poorly to water. If a piece has stood in the damp for a long time, the layers come apart. You see it in edges that gape or in a bulge in the surface. Press on it gently: it should not give or creak anywhere.

On chair shells, look for small cracks where the shell is fixed to the base, and at the narrowest point between seat and back. Look at the top layer of veneer as well. It is thin: if it was ever sanded too hard, the glue line beneath shows through as a dark patch.

Care in brief

Keep plywood dry and do not stand it against a radiator. Wipe it with a slightly damp cloth and dry it straight away. There is more in the book Caring for wood on the Care shelf.

Why we love it

Plywood is an honest material. It shows at the edge how it was made and does not pretend to be anything else. A chair of bent birch is light to look at and light to lift, and it takes up little space in a room: you look under it and past it. Against a white wall and on an old floor, that warm, matt wood gives just enough colour. You will find the pieces of plywood and bentwood from our collection below, and every one of them already has a life behind it. We ship worldwide.

Written by De Huiszwaluw

← Back to the library

For sale now

Plywood

Type
Price
1 on the wall

Looking for something in plywood?

Let us know. We buy every week and will tell you when something comes in. We ship worldwide.

Email a search request WhatsApp